When a tunnel catches fire, temperatures inside the concrete lining can soar to 800 or 900 degrees Celsius, and the emergency response almost always involves dousing the structure with water. A new study suggests that this familiar firefighting image—flames followed by a torrent of cooling water—may be doing far more damage to the concrete than engineers have typically accounted for. Researchers investigating basalt fiber-reinforced concrete have found that how a fire-damaged structure is cooled can be as important as how hot it got in the first place, with water quenching consistently inflicting greater strength loss than slow, natural cooling across every temperature they tested.

The research, published in Case Studies in Construction Materials, systematically examined how heating temperature, cooling regime, fiber content, and impact loading combine to determine whether concrete survives a fire with its load-bearing capacity intact. The team, led by Yang Liu and colleagues including Delin Li, Jinyue Dong, Yingda Zhang, Xianliang Zhou, and Qiong Zhou, chose basalt fiber-reinforced concrete, or BFRC, as their test material because of the fiber’s unusual combination of properties. Basalt fibers, drawn from volcanic rock, offer high tensile strength, thermal stability up to melting points between 1350 and 1450 degrees Celsius, and a cost profile far more attractive than premium alternatives such as carbon fiber. This makes them an appealing candidate for tunnel linings, where fire resistance and economy must be balanced.

The experimental design was exhaustive. The researchers prepared a C35-grade concrete mix—the grade commonly recommended for tunnel design—using ordinary Portland cement, medium sand, and continuously graded gravel between 5 and 10 millimeters. Into this base mix they incorporated chopped basalt fibers, 12 millimeters long with a monofilament diameter of 17 micrometers, at volume fractions of 0, 0.1, and 0.2 percent. The fibers were added in small batches during dry mixing to prevent agglomeration, and the fresh concrete was cast into cylindrical specimens measuring 50 millimeters in diameter and 25 millimeters in height, then cured under standard conditions at 20 degrees Celsius and 95 percent relative humidity.

The thermal assault began in a high-temperature electric oven capable of reaching 1200 degrees Celsius. Specimens were heated at a controlled rate of 5 degrees Celsius per minute to target temperatures of 200, 400, 600, and 800 degrees Celsius, then held at temperature for a full hour to ensure the heat penetrated the interior. Half the specimens were then removed and allowed to cool naturally in ambient air, mimicking a structure left to cool on its own after a fire. The other half were plunged immediately into a tank of tap water, replicating the thermal shock of firefighting operations. After cooling, the water-immersed specimens were conditioned in air for seven days to return them to a natural moisture state before testing.

The dynamic mechanical properties were then probed using a split Hopkinson pressure bar, the workhorse instrument for measuring how materials behave under the extreme strain rates produced by impacts and blasts. The apparatus used bars 75 millimeters in diameter, made of high-strength steel with an elastic modulus of 210 gigapascals, with a striker bar propelled by compressed gas striking an incident bar that transmitted stress waves through the specimen. Three impact velocities—3.5, 4.4, and 5.2 meters per second—were tested, achieved by varying the operating gas pressure, with three specimens per condition. A thin pulse shaper was pasted at the impact end of the incident bar to smooth out high-frequency oscillations, and stress equilibrium between the two faces of each specimen was verified from strain-gauge signals, confirming the reliability of the data. Fragments from each impact were sieved through meshes ranging from 4.75 millimeters down to 75 micrometers so that a fractal dimension could be calculated, providing a quantitative measure of how thoroughly each specimen shattered.

The visual evidence of thermal damage followed a familiar but telling progression. At 200 degrees Celsius, the concrete surfaces turned bluish-gray, with no cracking. By 400 degrees, the color shifted to yellowish-gray, still structurally sound. At 600 degrees, fine cracks appeared along with slight surface peeling, and by 800 degrees the specimens showed severe cracking, spalling, and edge breakage. Water-cooled specimens generally exhibited more pronounced surface damage than their naturally cooled counterparts, and at 800 degrees the concave shape at the start of the stress-strain curve—evidence of pre-existing microcracks being closed under compression—was especially marked in the water-quenched samples.

The strength data told a stark quantitative story. For naturally cooled specimens containing 0.2 percent basalt fiber, the dynamic peak stress at an impact velocity of 3.5 meters per second fell from 51.1 megapascals at room temperature to 18.6 megapascals at 800 degrees—a reduction of 63.6 percent. Water cooling made matters worse across the board: at the same impact velocity, the reductions reached 23.9 percent at just 200 degrees and climbed to 64.9 percent at 800 degrees. Averaged across the temperature range, each 100-degree increment cost naturally cooled specimens roughly 6.7 to 8.0 percent of their strength, while water-cooled specimens lost about 7.5 to 8.1 percent per 100 degrees. The gap between the two cooling regimes widened at higher impact velocities: at 5.2 meters per second and 800 degrees, the water-cooled specimens suffered 6.4 percent greater strength loss than the naturally cooled ones, whereas at the lowest velocity the difference was a mere 1.3 percent. The explanation lies in competing timescales—at slow loading rates, cracks have time to propagate and dissipate energy, blunting the effect of water-induced damage, but at high rates the loading outpaces the material’s energy dissipation, and the microcracks created by thermal shock propagate catastrophically.

Against this backdrop of degradation, the basalt fibers demonstrated genuine protective power. At every temperature from 200 to 800 degrees, specimens with 0.2 percent fiber content outperformed both plain concrete and the 0.1 percent mix. At 400 degrees and an impact velocity of 3.5 meters per second, the naturally cooled fiber-reinforced specimens reached peak stresses of 40.1 megapascals, some 16.9 percent above plain concrete, while at 200 degrees under water cooling the 0.2 percent mix achieved 38.8 megapascals—a remarkable 32.4 percent improvement over unreinforced concrete. The mechanism, the authors explain, is architectural: randomly distributed fibers form a three-dimensional network that binds tightly with the cementitious matrix, reduces internal pores and cracks, and bridges microcracks before they can coalesce into fracture surfaces. But this protection has a ceiling. Above roughly 600 degrees, the fibers begin to degrade and lose their reinforcing capability, and the fiber-matrix interface—already weakened by thermal mismatch between fiber and paste—becomes a liability during water quenching.

Fractal analysis of the impact debris added another layer of insight. The fractal dimension of the fragments rose steadily with temperature, from around 1.82 at 200 degrees to above 2.3 at 800 degrees under the highest loading rate, indicating progressively finer and more complex fragmentation. Water-cooled specimens consistently shattered into finer pieces than naturally cooled ones, particularly at 600 and 800 degrees, confirming that the steep thermal gradients during quenching seed dense populations of microcracks that later explode into fracture networks under impact.

Microstructural investigation grounded these observations in chemistry and physics. X-ray diffraction of specimens heated to 800 degrees showed the disappearance of calcium hydroxide peaks and weakened calcium carbonate signals, evidence that these phases had thermally decomposed—reactions that release vapor, increase porosity, and weaken the matrix. Scanning electron microscopy revealed the deterioration in vivid detail: an unheated specimen showed a dense microstructure with abundant calcium-silicate-hydrate gel and a compact interfacial transition zone around each aggregate, while specimens heated to 800 degrees contained no detectable C-S-H gel at all, their structure riddled with pores and cracks and hosting instead a dicalcium silicate-like phase. Comparing cooling regimes at 400 degrees, the naturally cooled sample remained relatively dense and rich in hydration products, whereas its water-quenched twin displayed obvious cracks at the interfacial transition zone and a loosened surrounding matrix—the fingerprint of thermal shock stress racing through the cooling material.

The practical implications reach well beyond the laboratory. Tunnel linings that survive a fire are routinely assessed and, if necessary, repaired, but this study shows that the assessment itself must account for the cooling history. A lining quenched by firefighting water may be significantly weaker than its peak temperature alone would suggest, particularly if it subsequently faces dynamic loads from traffic vibration, rockfall impacts, or secondary events. Conversely, the results give engineers a positive tool: specifying basalt fiber reinforcement at around 0.2 percent by volume can meaningfully bolster the impact resistance of fire-exposed concrete below 600 degrees, at a modest material cost. The authors frame their work as a theoretical foundation for post-fire safety assessment of tunnel linings and for the wider engineering adoption of basalt fiber-reinforced concrete—a reminder that in structural fire engineering, what happens in the minutes after the flames matter almost as much as the fire itself.

For four hours in July, some of the biggest players in finance put Wall Street’s long-running blockchain experiment to work across an ordinary trading day.

After years of tests with digital versions of securities, cash and trading networks, the focus has shifted to whether these technologies could work together. This time, nearly 40 firms were testing how tokenized assets could move through the institutions that keep modern markets moving.

Over blockchain networks, JPMorgan Chase & Co., Goldman Sachs Group Inc., Invesco Ltd. and Citadel Securities LLC traded stocks and Treasuries, posted collateral, met margin calls and transferred assets. Overseeing it all was the Depository Trust & Clearing Corp., which monitored the exercise from “war rooms” in New York and New Jersey as the firms completed dozens of transactions across various use cases.

The broader aim was to test whether tokenized versions of familiar assets can move through new blockchain systems without sacrificing the settlement, custody and risk controls of traditional markets.

“We tried to replicate the activities that occur in the market on a day to day,” said Nadine Chakar, DTCC’s global head of digital assets. “You don’t want tokenization to be done in isolation. You want it to be part of the daily workflow.”

That is the bet behind much of Wall Street’s tokenization push: not just longer operating hours as markets move toward 24/7 trading, but whether assets can move more freely across institutions, reducing trapped liquidity and some of the handoffs involved in moving collateral.

The July pilot was an attempt to test that proposition under something closer to real market conditions, bringing together exchanges, clearinghouses, banks and asset managers rather than limiting transactions to bilateral trades. Transactions included collateral pledges, margin calls, repo trades, delivery-versus-payment and transfers between blockchains using digital versions of stocks, exchange-traded funds and Treasuries on DTCC’s private network built using Besu and the Canton Network.

DTCC said it plans to move the service from limited tests toward ongoing use in October, adding another blockchain network, expanding support for Treasury corporate actions — coupon payment and Treasury maturity dates — and opening it to eligible participants beyond the July group.

DTCC’s role in the test was key because it maintains the official record for trillions of dollars of securities. If tokenized trades still have to be reconciled back to that traditional record at the DTCC, some of the promised efficiency disappears.

DTCC declined to provide transaction values or client-specific details. Chakar said “the purpose of the day was to simulate a representative snapshot of the market by including exchanges, clearing houses, buy-side and sell-side participants.”

Major hurdles remain, Chakar said, including adoption, regulatory alignment and integration with existing systems.

DTCC says Wall Street’s current tokenization push is different from previous attempts to deploy blockchain to financial markets because institutional demand has grown. The agency pointed to an industry working group that has nearly doubled in a few months to more than 100 members. Whether that matters commercially is a different question, said Vivian Fang, a finance professor at Indiana University.

“Many enterprise blockchain pilots over the past decade failed not because the technology didn’t work, but because they lacked the conditions needed for commercial adoption,” she said. “The ultimate test will be whether market participants meaningfully adopt tokenized securities and whether the platform delivers measurable economic value.”

Collateral Movement

Collateral offered one of the clearest tests of whether tokenization has economic value. In one transaction, DTCC tokenized an equity it held and deployed it as margin at CME Group Inc. within minutes. Tokenized collateral can settle almost instantly, potentially reducing trapped liquidity and allowing firms to put assets to work more efficiently, Chakar said.

JPMorgan, participating as a DTCC clearing member, separately converted securities collateral into digital tokens and used them to fund a margin call. The bank also tested tokenized equity collateral, including Invesco’s Nasdaq 100 ETF, ticker QQQ.

“Tokenization could reduce friction, improve collateral mobility and enable assets to be deployed more efficiently in support of margin requirements,” said Danny Hand, digital assets lead for prime financial services at JPMorgan.

There is a catch. JPMorgan can create tokenized collateral, but clearinghouses still have to accept it, custodians have to handle it and risk systems have to account for it. Broader adoption will depend in part on central counterparties recognizing tokenized collateral after DTCC expands the service.

That helps explain why early adoption may cluster around a handful of uses. Citigroup Inc. has projected tokenized assets could reach $5.5 trillion by 2030, rising to $8.2 trillion in a bullish scenario. Bank of America Corp. Global Research analysts expect early adoption to focus on collateral mobility, on-chain cash management and settlement of standardized financial instruments, with stocks and credit developing more gradually.

Legal clarity remains another obstacle, according to Noelle Acheson, author of the “Crypto Is Macro Now” newsletter. But DTCC is “in the relatively unique position of being able to move the industry forward by setting standards and working with global partners,” she noted. “That said, the transformation is likely to take about a decade.”

Even if those uses take hold, another problem remains: firms are building on blockchain networks that do not automatically communicate. Moving an asset between them still requires both systems to agree on what moved and who owns it.

The July transactions also tested whether separately built systems could work together. Digital Asset Holdings LLC’s Canton Network underpinned several of those trades.

“It was a real functioning secondary market set of activities that was enabled by market participants,” said Kelly Mathieson, the company’s chief business development officer.

For all the activity in July, the exercise was carefully choreographed. Participants spent months testing together in an intentionally narrow window and a relatively small amount of assets were converted into an onchain form. October begins the harder phase: whether the system gets used by a larger group during the course of everyday business.

“It was a massive step for the market and for the overall state of readiness for all participants come October,” Chakar said. “There’s nobody questioning anymore whether the technology works.”

Read full story here…

A multidisciplinary team from Baylor College of Medicine, Rice University and the University of Texas School of Public Health has received the inaugural Climate + Health Excellence award from the Burroughs Wellcome Fund. The five-year, $10 million award will support FORECAST, an ambitious program designed to investigate how climate change, extreme weather and environmental disruption influence the emergence and spread of infectious diseases. Led by infectious disease researcher Dr. Anthony Maresso, the project will combine wastewater surveillance, metagenomic sequencing, climate science, epidemiology and public education to create an early-warning system for pathogen activity across Texas.

FORECAST will build on Texas’s expanding wastewater-monitoring infrastructure, including the Texas Wastewater Environmental Biomonitoring Network, or TexWEB. The statewide network samples sewage from 15 Texas cities and analyzes biological material shed by communities. Unlike clinical surveillance, which depends on people seeking medical care and receiving diagnostic tests, wastewater epidemiology captures population-level signals from entire communities. Viral genetic fragments, bacterial DNA and other biological markers can appear in sewage before hospitals and clinics register a rise in patients, providing public health officials with valuable time to investigate and respond.

The program will use metagenomic surveillance, a technique that examines genetic material recovered from environmental samples rather than searching only for a predetermined pathogen. In conventional testing, laboratories typically use targeted molecular assays designed to detect a known virus or bacterium. Metagenomic sequencing can survey a much broader range of organisms, including variants and potentially unfamiliar pathogens. Researchers can then compare these signals with clinical data, geographic information and environmental measurements to determine whether changes in temperature, rainfall, flooding, drought or other conditions are associated with shifts in infectious disease activity.

The scientific goal is not simply to identify pathogens after they appear, but to uncover relationships between microbes and the environmental conditions that help them enter or circulate within human populations. Climate change can influence disease transmission through several pathways. Warmer temperatures may expand the geographic range or seasonal activity of mosquitoes and other vectors. Heavy rainfall and flooding can overwhelm sanitation systems and redistribute contaminants, while drought can alter water use and concentrate biological material. Changes in human behavior, animal movement and ecosystems may create additional opportunities for pathogens to cross species boundaries.

Maresso and his colleagues demonstrated during the COVID-19 pandemic that SARS-CoV-2 signals in wastewater could precede increases in clinically diagnosed infections. Viral RNA released in feces entered sewage systems, where researchers tracked changes in concentration over time. Although wastewater measurements cannot determine which individuals are infected, they can reveal whether pathogen activity is increasing or declining within a catchment area. The approach has since been extended to a wider range of targets, including avian influenza, measles, HIV and viruses associated with cancer. FORECAST aims to develop this surveillance capacity into a predictive climate-health platform.

Rice University climate scientist Dr. Sylvia Dee will help connect pathogen observations with weather and climate data. The team plans to examine whether specific environmental patterns consistently occur before increases in particular infectious agents. Such models could eventually function like a public health weather report, indicating when conditions are becoming more favorable for disease transmission. The researchers emphasize that predictive systems will require careful validation because the presence of pathogen genetic material does not necessarily indicate infectious virus, active transmission or a future outbreak. Interpreting the signal will require laboratory studies, clinical evidence and knowledge of local infrastructure.

The project will also investigate diseases transmitted by vectors such as mosquitoes. Dr. Peter Hotez and colleagues at the National School of Tropical Medicine will focus on vector-borne pathogen transmission and the growing health risks associated with changing climate conditions. Texas is particularly relevant for this work because it contains diverse ecological regions and experiences heat waves, hurricanes, flooding and rapid urban growth. These factors can affect mosquito habitats, human exposure and the movement of pathogens across communities. Integrating wastewater findings with vector surveillance could help reveal connections that would remain hidden if either system were used alone.

Education and public communication will form a central part of FORECAST. The team plans to create a “Middle to Medical” climate-health education track extending from middle school through medical training and professional development. Dr. Nancy Moreno, who developed Baylor’s BioEd online program, will lead educational efforts with Rice University’s Dr. Joseph Campana, director of the university’s Center for Environmental Studies and EcoStudio. The curriculum will explain how pathogens spread, how climate conditions alter disease risk and how scientific evidence can guide decisions by students, clinicians, policymakers and communities.

The award is particularly significant because FORECAST was selected as the sole funded project from 161 applications submitted to the new CHEX program. The initiative is intended to strengthen research, education and public engagement at the intersection of climate change and human health. Dr. Eric Boerwinkle, dean of the UT School of Public Health and a project co-investigator, will contribute access to large clinical datasets that can be used to evaluate wastewater and environmental signals against reported illnesses. The investigators say the work could improve outbreak preparedness while advancing the still-developing field of wastewater science.

By combining environmental sequencing with climate modeling and health education, FORECAST seeks to shift infectious disease surveillance from a largely reactive system toward earlier detection and prevention. Its findings may help officials recognize emerging threats before they produce widespread clinical disease, while also clarifying how environmental changes shape viral evolution, transmission and geographic spread. The researchers describe wastewater as an unusually candid public health resource: it aggregates biological information from a population without requiring individual testing. As climate pressures intensify, they argue, that collective signal could become an essential tool for protecting communities and preparing the next generation of scientists.

Subject of Research:
Climate-driven infectious disease emergence, wastewater epidemiology, metagenomic pathogen surveillance and climate-health education.

Article Title:
Texas Researchers Launch FORECAST Program to Link Climate Change With Emerging Viral Threats

Web References:
Baylor College of Medicine; Rice University; University of Texas School of Public Health; Burroughs Wellcome Fund; Texas Wastewater Environmental Biomonitoring Network (TexWEB).

References:
Information provided in the source news release concerning the FORECAST project, the Climate + Health Excellence award and TexWEB wastewater surveillance activities.

Keywords:
Wastewater epidemiology, viral surveillance, metagenomic sequencing, climate change, infectious diseases, pathogen emergence, public health, Texas, SARS-CoV-2, avian influenza, measles, vector-borne disease, climate health, epidemiology, wastewater science

PHILADELPHIA — Public resistance to new data centers has risen sharply across the United States, even as Americans’ overall views of artificial intelligence remain largely unchanged, according to a nationally representative survey from the Annenberg Public Policy Center at the University of Pennsylvania. The findings reveal a growing divide between public attitudes toward AI as a technology and attitudes toward the physical infrastructure required to operate it. While many people continue to see potential benefits from AI, particularly in medical research, opposition increases substantially when the technology is associated with a large industrial facility being built near their homes.

The survey found that 61% of U.S. adults somewhat or strongly oppose the construction of new data centers in their communities. That figure is 12 percentage points higher than the 49% recorded in an earlier APPC survey conducted in February and March. Support fell during the same period, from 21% to 14%. The change comes as communities across the country debate the environmental, economic, and social consequences of rapidly expanding computing infrastructure used to train and operate advanced AI systems.

Data centers are specialized facilities filled with servers, networking equipment, cooling systems, backup power supplies, and security infrastructure. AI applications can require enormous amounts of computational power because they process vast datasets and perform calculations across billions of model parameters. Training a large AI model may require thousands of processors operating simultaneously, while everyday use also depends on data centers to generate responses, analyze images, translate languages, and carry out other tasks. These facilities can consume substantial amounts of electricity and water, making their construction a highly visible local issue even when the software they support is used remotely.

Opposition to local data centers crosses political boundaries. Majorities of Democrats, Republicans, and independents said they opposed new facilities in their areas, although the proportions differed: 69% of Democrats, 54% of Republicans, and 53% of independents expressed opposition. Resistance was strongest among adults younger than 30, reaching 70%, and declined to 57% among people 65 and older. The pattern is notable because younger adults are often assumed to be more comfortable with emerging technologies and are more likely to use AI-powered services in education, work, entertainment, and communication.

Despite the shift in views about local infrastructure, broader opinions about AI have remained stable. Thirty-nine percent of respondents said they expected AI’s impact on the United States over the next decade to be somewhat or very negative, compared with 18% who expected a positive impact. The result was statistically unchanged from the spring survey. In addition, 68% said the federal government has done “too little” to regulate AI, a view shared by majorities of Democrats, Republicans, and independents. The results suggest that concerns about AI regulation have become persistent rather than being driven solely by short-term news events.

Respondents distinguished sharply between areas where AI might produce public benefits and areas where it could create risks. Among 13 sectors examined, medical research and scientific discovery was the only category receiving a net-positive assessment, with anticipated benefits exceeding expected harms by 41 percentage points. AI systems are increasingly being used to identify patterns in biological data, predict molecular structures, assist with medical imaging, and help researchers screen potential treatments. These applications may accelerate work that would otherwise require years of laboratory experiments, although they still depend on human validation and carefully controlled clinical studies.

The most negative assessments involved personal privacy and data security, which registered a net score of minus 63 points. Children’s online safety followed at minus 50 points, while employment and jobs reached minus 46 points. These concerns reflect the technical and social consequences of deploying AI at scale. Models may be trained on or exposed to sensitive information, automated systems can make decisions that are difficult to explain, and workplace applications may alter or eliminate certain tasks. The survey does not measure whether these risks will materialize in specific industries, but it indicates that many Americans view them as more immediate than AI’s possible benefits outside medicine.

Personal experience with AI was associated with more favorable opinions about its national impact. Among respondents who said they had never used AI during the previous month, 54% expected its effect on the country to be negative. That proportion fell to 40% among light users and to 29% among those who used AI many times or almost every day. However, frequent use did not make people more supportive of data centers. Opposition to building new facilities near respondents’ homes remained essentially flat across different levels of AI use. This distinction suggests that familiarity may influence perceptions of digital tools, while concerns about electricity demand, water consumption, noise, traffic, land use, and local utility costs may remain regardless of personal experience with AI software.

“The people who use AI the most are the most optimistic about what it will do for the country, and that has been consistent across our surveys,” said Matt Levendusky, a University of Pennsylvania political science professor and the Stephen and Mary Baran Chair in the Institutions of Democracy at APPC. He said that optimism had clear limits, particularly when questions involved privacy, employment, or the construction of a data center nearby. The survey was conducted by SSRS for APPC’s Institutions of Democracy division among 1,320 U.S. adult citizens from June 16 through July 19, 2026. Respondents were surveyed primarily online, with a small telephone sample, and weighted to match population benchmarks. The margin of error for the full sample was plus or minus 3.5 percentage points, with larger margins for subgroups. Together, the findings indicate that the next phase of the AI debate may be shaped less by abstract promises about intelligent software than by negotiations over the highly physical systems that make it possible.

Subject of Research: People

Article Title: Opposition to Local Data Centers Rises Sharply as Views on AI Hold Steady

Web References: Annenberg Public Policy Center news release; Reuters; The New York Times; Associated Press

References: Annenberg Public Policy Center Institutions of Democracy national survey, June 16–July 19, 2026; APPC AI topline survey data; APPC survey methodology

Image Credits: Annenberg Public Policy Center

Keywords: Artificial intelligence, data centers, public opinion, AI regulation, medical research, privacy, data security, employment, social surveys, political science

A new study is challenging one of the most persistent assumptions in space manufacturing: that building advanced composite structures beyond Earth is simply a matter of moving terrestrial production methods into orbit. Research published in npj Advanced Manufacturing examines how two defining features of the space environment—reduced gravity and reduced atmospheric pressure—can alter the manufacture of carbon-fiber-reinforced structures, materials widely regarded as essential for future spacecraft, habitats and large orbital infrastructure.

Carbon-fiber-reinforced polymers, commonly known as CFRPs, combine strong, lightweight carbon fibers with a polymer resin that binds the fibers into a rigid composite. Their exceptional strength-to-weight ratio makes them attractive for launch vehicles and spacecraft, where every kilogram matters. Yet manufacturing these materials is a delicate process. Fibers must be positioned accurately, resin must penetrate the reinforcement evenly, and gases or trapped voids must be removed before the material cures. On Earth, gravity and atmospheric pressure quietly assist—or complicate—each of these steps.

In space, those familiar forces change dramatically. Reduced gravity can alter how liquid resin flows through a carbon-fiber structure, while low pressure can encourage dissolved gases and volatile compounds to expand or escape. Together, these effects may influence impregnation, consolidation, curing and the final mechanical performance of a composite part. The new work by R. Strecker, T. Rieger, A. Tabelander and colleagues focuses on understanding these interactions before manufacturers attempt to produce increasingly complex structures in orbit.

The central issue is void formation. A composite that appears solid can contain microscopic pockets of air or vapor between its fibers. These voids interrupt the transfer of stress through the material and can reduce strength, stiffness and fatigue resistance. During conventional manufacturing on Earth, pressure is often applied to compress the layers and drive out unwanted gases while resin fills the spaces between fibers. In a reduced-gravity environment, however, buoyancy-driven movement is weakened, and the pathways through which bubbles travel may change. A bubble that would rise and escape during terrestrial processing could remain trapped inside the structure.

Pressure reduction introduces another layer of complexity. Lower ambient pressure can help remove volatile substances and trapped gases, but it can also cause dissolved gases in the resin to expand. If the resin is not sufficiently mobile, expanding bubbles may become locked in place as the material cures. The balance between degassing and bubble growth therefore becomes a critical manufacturing parameter. The study’s importance lies in treating pressure and gravity not as isolated variables, but as environmental conditions that can interact throughout the production cycle.

Resin flow is equally important. Carbon-fiber reinforcements are made from tightly packed filaments, creating narrow channels through which resin must travel. On Earth, gravity can influence resin distribution, especially in vertically oriented or large components. In reduced gravity, capillary forces and surface tension become relatively more significant. These forces can help draw resin into small spaces, but they may also create uneven wetting patterns depending on the fiber architecture, resin viscosity and processing orientation. Such changes could affect whether a component cures uniformly from its surface to its interior.

The findings carry implications far beyond laboratory samples. Future space manufacturers may seek to fabricate beams, pressure-vessel elements, antenna supports, solar-array components and repair patches directly in orbit. Producing these parts where they are needed could reduce the need to launch bulky finished structures from Earth. It could also enable designs too large to fit inside a rocket fairing, including trusses and habitation modules assembled gradually in space. But the economic and engineering promise of this approach depends on reliable quality control. A component that looks flawless may still fail if its internal fiber alignment, resin distribution or void content is inconsistent.

The research also highlights why manufacturing hardware designed for Earth cannot automatically be considered space-ready. Pumps, heaters, vacuum systems, molds and curing chambers must all operate under conditions in which heat transfer, fluid movement and gas removal behave differently. Temperature control is particularly important because resin viscosity changes strongly with temperature. A resin that flows readily during terrestrial processing might move more slowly or unevenly in orbit, while excessive heating could accelerate curing before impregnation is complete. Space-based production systems will therefore need carefully coordinated control of pressure, temperature, resin chemistry and processing time.

For engineers, the study provides a foundation for developing manufacturing protocols tailored to reduced-gravity environments. Instead of copying Earth-based workflows, future systems may need staged pressure changes, specialized fiber preforms, modified resin formulations or active bubble-management techniques. Sensors could monitor pressure, temperature and resin flow in real time, allowing automated systems to detect defects before a part is finished. Non-destructive inspection, including imaging and ultrasonic testing, will also be essential for verifying the integrity of components that cannot easily be returned to Earth for analysis.

The broader message is that space manufacturing is not merely an extension of industrial production—it is a new manufacturing regime governed by different physics. Understanding how gravity and pressure reshape the behavior of fluids, gases and composite materials could determine whether orbital fabrication remains a promising experiment or becomes a practical industrial capability. By examining the production of carbon-fiber-reinforced structures under space-relevant conditions, Strecker, Rieger, Tabelander and their colleagues are helping identify the hidden variables that will decide how safely and efficiently humanity can build beyond Earth.

Subject of Research: Effects of reduced gravity and reduced atmospheric pressure on the in-space manufacturing of carbon-fiber-reinforced structures

Article Title: Effects of reduced gravity and reduced atmospheric pressure on in-space manufacturing of carbon-fiber-reinforced structures

Article References: Strecker, R., Rieger, T., Tabelander, A. et al. Effects of reduced gravity and reduced atmospheric pressure on in-space manufacturing of carbon-fiber-reinforced structures. npj Adv. Manuf. 3, 26 (2026). https://doi.org/10.1038/s44334-026-00104-w

Image Credits: AI Generated

DOI: https://doi.org/10.1038/s44334-026-00104-w

Keywords: in-space manufacturing, carbon-fiber-reinforced polymers, reduced gravity, reduced atmospheric pressure, composite materials, resin flow, void formation, space technology

Federal-state stoush comes as rating agency warns that electricity bills could skyrocket

• Follow our Australia news live blog for latest updates

• Get our breaking news email, free app or daily news podcast

Queensland and the Northern Territory have rejected the federal government’s plans to mandate that AI datacentres use renewable power, rubbishing Anthony Albanese’s proposals to regulate the booming technology as “underdeveloped ideas that hand increased power to Canberra”.

The latest federal-state stoush on energy comes as S&P Global, the economic rating agency, warns that power use from datacentres could rise five-fold by 2035 to 10% of Australia’s total consumption, and that a mismatch between delivery timelines for datacentres and renewable projects could lead to energy bills skyrocketing.

A new study in npj Urban Sustainability points to the practical levers that determine whether stormwater systems actually deliver long-term sustainability. As cities expand and rainfall extremes intensify, green and nature-based infrastructure has been promoted to capture runoff, reduce flooding, and protect water quality. But the research warns that success is not automatic: design decisions and operational realities can make or break performance.

The authors, Sun, Randrup, Blecken and colleagues, analyze what they call “decisive factors” governing sustainable stormwater management. Their central message is that the most visible features—such as bioswales, permeable surfaces, or detention basins—only work when supported by the right planning assumptions and measurable hydrological outcomes.

A key technical theme is how stormwater must be matched to system capacity under changing conditions. The study emphasizes that system sizing, soil or media properties, and infiltration or storage behavior strongly influence whether the infrastructure can handle typical storms and rare, high-intensity events. When these factors are misestimated, treatment efficiency can collapse during peak flows.

Equally important are maintenance and lifecycle considerations. Sustainable stormwater is sensitive to clogging, sediment accumulation, vegetation health, and changes in catchment behavior. The research highlights the need for maintenance regimes that reflect likely failure modes, rather than generic schedules that ignore local hydrology and traffic or land-use impacts.

The paper also stresses the value of monitoring and model-informed decision-making. Reliable data on rainfall patterns, runoff routing, and pollutant loads allow managers to validate performance and adjust operations. This feedback loop helps prevent long-term degradation that otherwise remains invisible until issues become costly.

For cities seeking viral, widely transferable “what works” guidance, the authors’ findings offer a shortlist of priorities: realistic capacity planning, robust material characterization, design for multi-storm performance, and maintenance strategies tied to specific mechanisms. Together, these elements translate sustainability goals into systems that function under real weather and real urban change.

The study’s DOI is 10.1038/s42949-026-00448-4.

Subject of Research: Sustainable stormwater management / urban sustainability
Article Title: Decisive factors in sustainable stormwater management
Article References: Sun, Z., Randrup, T.B., Blecken, GT. et al. Decisive factors in sustainable stormwater management. npj Urban Sustain 6, 104 (2026). https://doi.org/10.1038/s42949-026-00448-4
Image Credits: AI Generated
DOI: https://doi.org/10.1038/s42949-026-00448-4

Our modern society depends heavily on communications and power networks that are highly susceptible to interference from solar storms, making these volatile space weather events a paramount concern for scientists.

Now, it turns out there may be more to fear than previously realized. Scientists are discovering that there may be no ceiling to the devastating effects solar storms may have on Earth, overturning what little sense of security may exist as a mere mathematical anomaly.

In a recent paper published in Nature, a NASA-led team discovered that the potential impact of solar storms on our technological infrastructure could be substantially more severe than currently recognized.

Solar Storms Reconsidered

According to new research, any past limitations perceived regarding the impact of solar storms on our planet are purely an illusion, which arises from imprecise data collection.

Previous observations of electric currents in the Earth’s upper atmosphere during solar storm events suggested a ceiling to how far they could increase. Yet the new paper claims that uncertainties in solar wind data are falsely giving rise to this idea.

The researchers say that the distance of the spacecraft taking solar wind measurements is the issue. Those spacecraft are millions of miles closer to the Sun than the Earth is, meaning that by the time those winds reach Earth, they have weakened considerably. Additionally, instrument error and the effects of the local plasma and field conditions all come into play.

All this, the researchers say, creates a mismatch between the measured strength of the wind and its effects on our planet’s electrical currents.

Correcting For Distance

The new findings contain one significant difference from existing research: they relied on observation platforms much closer to Earth to collect data, which included spacecraft such as NASA’s MMS and THEMIS.

Launched in 2007, THEMIS consists of five satellites that target the Earth, rather than the Sun, to study our planet’s magnetosphere and auroras. MMS consists of four spacecraft that also study the Earth’s magnetosphere.

Existing charts show the impact of solar winds on Earth leveling off at a certain threshold, which scientists had believed was the maximum saturation possible. However, in new solar wind strength data collected much closer to Earth, more accurately reflecting power at the time of impact, this saturation point disappeared. Instead, this data revealed that there is no ceiling on how heavily solar storms can charge the Earth’s electrical currents.

Solar Storm Impacts

Another crucial element in the NASA-led research is the statistical concept of regression to the mean, which holds that extreme measurements often change as more data come in. In this case, as more data on solar storm impacts on Earth recorded from various distances were collected, the plating effect disappeared. The authors note that similar effects occur in other areas of research, such as climate studies and chronic medical pain.

These new findings present a major challenge to our understanding of space weather. Scientists will now need to conduct many further observations to determine if any such ceiling exists. The threat to our infrastructure may be severe, as satellite communication underpins our modern society, not to mention the power grid, which keeps our world running.

For now, NASA continues to monitor solar storms to prepare for their potentially dangerous effects on our infrastructure, and in light of the new research, the potential for future challenges ahead may be greater than previously realized.

The paper, “Regression to the Mean Can Explain Saturation of Geomagnetic Storms,” appeared in Nature on July 15, 2026.

Ryan Whalen covers science and technology for The Debrief. He holds an MA in History and a Master of Library and Information Science with a certificate in Data Science. He can be contacted at ryan@thedebrief.org, and follow him on Twitter @mdntwvlf.

Climate change is poised to reshuffle the reliability problem facing decarbonized power systems, according to a new study that links weather extremes, long-term climate projections, and real-world infrastructure constraints. As grids rely more heavily on wind and solar, they become sensitive not just to the amount of renewable capacity installed, but to where that capacity is sited relative to transmission lines, load centers, and the local meteorological patterns that govern output.

Using high-resolution climate projections at 12-km scale, the researchers examined how future conditions could alter both renewable generation and electricity demand across two distinct US regions: New England and Texas. They then coupled these climate inputs with an optimization model operating at the county level, allowing the team to test how system design choices—particularly spatial siting of wind and solar and the presence of transmission bottlenecks—affect long-run adequacy.

The results suggest a sharp increase in resource inadequacy risk by mid-century. In both regions, climate change can drive prolonged periods of low renewable generation, which occur when meteorological conditions reduce wind and solar output while demand simultaneously rises. For Texas, the study finds the frequency of inadequacy events could increase dramatically—up to fivefold—if planning proceeds using non-climate-informed assumptions.

Crucially, the work shows that these risks are not determined by aggregate capacity targets alone. Fine-scale siting decisions can lock the system into unfavorable “weather-resource–grid” pairings, amplifying periods when local supply falls short and transmission limits prevent imports from compensating.

Yet the study also offers a pathway to resilience. Climate-informed planning can mitigate the emerging adequacy threat at relatively modest cost. Texas, for example, can maintain near-zero marginal investment cost by shifting wind capacity westward, improving alignment with future wind patterns and reducing reliance on constrained transfers.

New England requires a different strategy. The region faces a higher investment need—about a 2.34% increase—achieved through targeted solar and transmission expansion closer to load centers. This approach helps buffer localized shortfalls during future, climate-driven demand and renewable output mismatches.

Overall, the study argues that achieving climate-resilient decarbonization means moving beyond simple build-out schedules. Instead, it calls for high-resolution, climate-aware spatial planning that reveals siting opportunities invisible to coarse models—turning reliability from a static design metric into a dynamic, region-specific forecast problem.

Subject of Research: Climate change and resource adequacy risks in wind/solar grids, including optimal renewable siting
Article Title: Climate change reshapes resource adequacy risks and optimal renewable energy siting in wind and solar energy systems
Article References: Qiu, L., Khorramfar, R., Wang, S. et al. Climate change reshapes resource adequacy risks and optimal renewable energy siting in wind and solar energy systems. Nat Energy (2026). https://doi.org/10.1038/s41560-026-02109-3
Image Credits: AI Generated
DOI: https://doi.org/10.1038/s41560-026-02109-3
Keywords:

In a groundbreaking decade-long study analyzing São Paulo’s urban landscape, researchers have revealed how the expansion of bike lanes and public parks profoundly influences physical activity and public health. Between 2014 and 2024, the city’s bike lane network surged from 242 to 743 kilometers, complemented by the addition of 15 municipal parks. This urban transformation was linked to increased transport-related cycling, emphasizing the critical role of accessible infrastructure within a 500-meter radius of residents’ homes.

The study’s multidisciplinary approach combined longitudinal surveys of 1,500 residents with geospatial datasets from the Geosampa platform, enabling precise correlation between environmental changes and behavior. Findings indicate that proximity to bike lanes significantly counteracts declining bicycle use trends, suggesting these facilities serve as protective factors promoting sustained physical activity. Such activity reduction directly translates to lower risks of cardiovascular disease, cancer, and improved mental health outcomes like reduced anxiety and depression.

Importantly, the research underscores active transportation infrastructure not only as a logistical planning tool but as a vital public health strategy. By reducing reliance on automobiles, these interventions diminish air pollution and traffic-related accidents, thereby contributing to climate change mitigation efforts. However, the study highlights uneven developments: wealthier neighborhoods received disproportionate infrastructure investments, calling for policy shifts to equip underserved zones with similar amenities.

Beyond infrastructural improvements, the researchers emphasize that sociocultural elements and affordability constraints also limit cycling uptake. Despite increased bike lanes, economic barriers such as the high cost of bicycles and gender disparities in cycling participation suggest that integrated approaches—encompassing recreational street design, bike-sharing expansions, and commuter support facilities—are necessary for meaningful behavioral shifts.

An illustrative testimony comes from a local photographer who transitioned from motorbike to bicycle commuting due to new bike bridges providing direct, safer routes. While embracing cycling’s growth, he voices concerns about road space allocation favoring cars and the emerging challenges of cyclists’ vulnerability amid the rise of faster electric bikes. Additionally, issues of public safety and bike theft remain barriers to broader adoption.

Overall, the findings reveal that São Paulo’s urban planning efforts over the past decade represent a promising model of how thoughtfully designed public open spaces can foster healthier, more sustainable cities. Still, ensuring equitable access and addressing multifaceted cultural and socioeconomic factors remain essential for realizing the full potential of active transport systems.

Subject of Research: Public open spaces and transport-related cycling in urban environments
Article Title: A decade-long study on public open spaces and transport-related cycling in the largest Brazilian city
News Publication Date: 13-Apr-2026
Web References: https://dx.doi.org/10.1016/j.jth.2026.102323
Image Credits: Phelipe Janning/Agência FAPESP

Keywords

Urban planning, Transportation, Public health, Cycling, Active transportation, São Paulo, Infrastructure, Mental health

They suck up energy and water, and blast out heat. Just who is better off from all this investment – aside from tech bros?

The two great existential threats of our time – the climate crisis and AI – come hurtling together in the explosion of datacentres across Australia and around the world.

You can hardly avoid hearing about them these days, either with awed reverence of the promised benefits to humankind or with fear and anger given the implications for the climate, inflation, jobs and even housing affordability.

St. Jude Children’s Research Hospital has reaffirmed its pivotal role in the global fight against pediatric cancer with its recent redesignation as a World Health Organization (WHO) Collaborating Centre for Childhood Cancer. This prestigious status not only honors St. Jude’s deep-rooted commitment to advancing pediatric oncology but also solidifies its unique position as the sole WHO Collaborating Centre exclusively dedicated to childhood cancer worldwide. The designation reflects the hospital’s substantial contributions in providing strategic, scientific, and technical expertise to WHO’s mission, thereby accelerating progress in improving survival rates and care quality for children afflicted by cancer internationally.

At the heart of this collaboration lies a fundamental conviction championed by St. Jude: a child’s geographic location must never dictate their likelihood of surviving cancer. Under the leadership of Dr. James R. Downing, St. Jude’s President and CEO, the institution actively partners with global health bodies, governments, academic institutions, and clinical providers to broaden access to comprehensive cancer care. These alliances are designed to fortify health infrastructures and knowledge exchange systems, ensuring equitable delivery of lifesaving therapies and supportive services for pediatric patients, irrespective of their origin.

St. Jude’s designation is not isolated but part of a sophisticated network of over 800 WHO collaborating centers distributed across more than 80 nations. Uniquely, St. Jude is dedicated exclusively to pediatric malignancies, making it an unparalleled resource in formulating childhood cancer policies and disseminating best practices. Since its inception as a WHO Collaborating Centre in 2018, St. Jude has leveraged its expertise to influence national health policies, boost technical capacity, and nurture multisectoral collaborations. These endeavors have collectively enhanced the global capacity to prevent, diagnose, and treat childhood cancers, shaping a more coordinated and effective response to pediatric oncology challenges.

The influence of St. Jude’s WHO Collaborating Centre extends significantly through the St. Jude Global Alliance, which encompasses over 400 institutions and foundations in more than 90 countries. This expansive network forms a robust implementation infrastructure that translates scientific discoveries into real-world improvements in pediatric cancer outcomes. As described by Dr. Catherine Lam, the Centre’s Director and a faculty clinician-scientist, this alliance fortifies the hospital’s academic and clinical expertise on an international scale, fostering innovation and knowledge transfer essential for tackling global disparities in pediatric oncology.

One of the landmark achievements stemming from this collaboration was the establishment of the WHO Global Initiative for Childhood Cancer (GICC) in 2018. This ambitious program targets a doubling of survival rates globally, aiming for at least 60% survival for childhood cancers by 2030. Complementing this, the 2025 launch of the Global Platform for Access to Childhood Cancer Medicines underscores a coordinated approach to overcoming barriers in medication availability and affordability—critical hurdles in low- and middle-income countries where cure rates have historically lagged behind.

The expanded remit of the WHO Collaborating Centre now includes not only oncology but also the management of catastrophic pediatric diseases such as sickle cell disease, representing an integrated strategy that acknowledges the complex medical and supportive care needs of these patient populations. This progression enhances the Centre’s potential to impact child health comprehensively, integrating palliative care and systems strengthening into its core objectives.

Driving the Centre’s evolving agenda, Dr. Carlos Rodriguez-Galindo, Executive Vice President and Chair of the Department of Global Pediatric Medicine, emphasizes the aim to ameliorate survival rates in regions where it has remained below 30%. Expanding the scope of pediatric care to encompass palliative services and holistic disease management initiatives ensures that children everywhere receive not only curative treatments but also dignified, comprehensive care throughout their disease trajectory.

The WHO recognizes the critical role of collaborating centers such as St. Jude in facilitating technical support, knowledge dissemination, and health system strengthening at the country level. According to Dr. Roberta Ortiz, medical officer at WHO Headquarters and focal point for the GICC, these centers bring invaluable expertise and tools that underpin successful implementation of global childhood cancer strategies. This partnership model is instrumental in translating high-level policy into practical actions that directly benefit pediatric populations.

St. Jude’s profound impact on national cancer control planning ensures that pediatric oncology is meaningfully integrated into broader health systems and governance frameworks. By embedding child-specific needs within policy platforms, the hospital advances a child-centered approach to cancer care that elevates research-driven innovations and frontline clinical breakthroughs. This comprehensive strategy enhances survivorship and quality of life for pediatric patients on a global scale.

In addition to its leadership in pediatric oncology, St. Jude also maintains a longstanding designation as a WHO Collaborating Centre for Influenza, a role it has fulfilled since 1975. This dual recognition highlights the institution’s diverse expertise and sustained contributions to global health, reaffirming its status as a vanguard institution whose research and clinical programs catalyze transformative progress across multiple domains of pediatric medicine.

St. Jude Children’s Research Hospital’s redesignation as the exclusive WHO Collaborating Centre dedicated to childhood cancer embodies the epitome of global health collaboration. Anchored in robust scientific inquiry, innovative care models, and strategic partnerships, this status propels forward a shared vision of equitable cancer care access and improved outcomes for all children—irrespective of geography. As the global pediatric oncology landscape evolves, St. Jude’s leadership and expansive alliance ensure that the journey toward eradicating childhood cancer is both scientifically rigorous and compassionately inclusive.

Subject of Research: Pediatric cancer, childhood oncology, global health collaboration

Article Title: St. Jude Reaffirmed as WHO Collaborating Centre Driving Global Pediatric Cancer Progress

News Publication Date: June 17, 2026

Web References:

• https://www.stjude.org/research/departments/global-medicine/who-collaborating-centre-for-childhood-cancer.html
• https://www.stjude.org/global/collaborating-to-cure/global-initiative.html
• https://global.stjude.org/en-us/featured/global-platform-for-access-to-childhood-cancer-medicines.html

Image Credits: St. Jude Children’s Research Hospital

Keywords: Pediatric cancer, Childhood cancer survival, WHO Collaborating Centre, Global pediatric oncology, St. Jude Global Alliance, Childhood cancer treatment access, Global Initiative for Childhood Cancer, Pediatric oncology research

In the ever-evolving landscape of biomedical research, the advent of molecular dynamics simulations has heralded a new era of insight into the dynamic behavior of biological macromolecules. Yet, despite the immense volumes of data generated by these simulations, much remains untapped due to the lack of adequate infrastructure for storage, sharing, and reuse. Addressing this critical gap, the MD4SB (Molecular Dynamics for Structure-based Biology) project emerges as a visionary initiative poised to revolutionize how molecular dynamics data is integrated, managed, and exploited across Europe.

Set to launch in September 2026, MD4SB is a collaborative endeavor funded with €10 million under the Horizon Europe program and coordinated by the Institute for Research in Biomedicine (IRB Barcelona). The project unites 25 partners spanning eight countries, encompassing academic institutions, European research infrastructures, supercomputing centers, as well as biotech and pharmaceutical companies. By doing so, it offers a multidisciplinary approach aimed at transforming fragmented computational efforts into a coherent, accessible, and reusable resource for the scientific community.

At the core of MD4SB is the establishment of an innovative infrastructure designed to dynamically describe biological macromolecules through molecular dynamics data. Unlike traditional structural biology methods that primarily capture static snapshots of molecules, molecular dynamics simulations reveal the conformational flexibility and temporal evolution of proteins and nucleic acids. This dynamic information is crucial for fully understanding molecular function, interaction mechanisms, and especially drug binding processes, thus providing a more nuanced picture for drug discovery initiatives.

MD4SB builds on the foundations laid by the Molecular Dynamics Data Bank (MDDB), which pioneered a distributed platform adhering to the FAIR principles—making data Findable, Accessible, Interoperable, and Reusable. The project advances this concept by integrating molecular dynamics data within three major European Research Infrastructures: Instruct-ERIC, which specializes in structural biology; ELIXIR, focused on life sciences data management; and EU-OPENSCREEN ERIC, a chemical biology and compound screening infrastructure. This integration ensures that molecular dynamics data becomes a shared asset rather than an isolated entity confined to individual laboratories.

Leveraging the capabilities of Europe’s largest supercomputing centers—specifically the Barcelona Supercomputing Center (BSC-CNS), CINECA in Italy, and the Jülich Supercomputing Centre (JSC)—MD4SB provides the computational muscle necessary for processing, storing, and analyzing massive datasets. These centers, combined with emerging AI Factories, will enable cutting-edge analysis pipelines that augment traditional molecular dynamics approaches with artificial intelligence, thus enhancing the extraction of biologically meaningful patterns from complex simulations.

One of the landmark objectives of MD4SB is to catalyze early drug discovery by enabling scientists to visualize the dynamic movements of proteins and other biomolecules that are often invisible in static crystal structures. Molecular dynamics simulations can reveal transient binding pockets and allosteric sites, which are pivotal for designing new therapeutic compounds with higher specificity and efficacy. By facilitating access to these insights within existing infrastructures, MD4SB aims to speed up the identification of drug candidates and reduce costly experimental failures.

Industry engagement lies at the heart of MD4SB’s strategy. Leading pharmaceutical companies such as Almirall and Sanofi are involved as associate partners, providing critical feedback to ensure that the developed platform not only serves academic research but also aligns with industrial requirements. The involvement of Nostrum Biodiscovery—a biotech spin-off from IRB Barcelona and BSC-CNS—further exemplifies the project’s commitment to bridging the gap between fundamental research and commercial application by easing the transition of innovations into practical tools.

Dr. Modesto Orozco, coordinator of MD4SB and head of the Molecular Modelling and Bioinformatics laboratory at IRB Barcelona, highlights the transformative potential of this initiative: “For the first time on a European scale, MD4SB will merge structural biology, molecular dynamics, artificial intelligence, and drug discovery into a seamless ecosystem. Our vision is to democratize molecular dynamics, making it a common capability accessible to researchers across disciplines.”

The strategic approach of MD4SB entails the seamless coupling of three complementary research infrastructures, encompassing the full spectrum of biomedical research phases: from structural protein characterization, data stewardship and interoperability, to chemical biology screening for therapeutic potentials. This holistic integration enables unprecedented collaborative workflows, where data generated in one context can be analyzed, reanalyzed, and repurposed across diverse scientific domains.

Central to the success of MD4SB will be its adherence to data standards and protocols that guarantee FAIR compliance, ensuring that the vast repositories of molecular dynamics simulations remain discoverable and usable well beyond the lifespan of individual projects. This commitment is indispensable in preventing the loss of valuable computational endeavors, promoting reproducibility, and fostering innovation driven by shared resources.

By significantly expanding the accessibility and applications of molecular dynamics data, MD4SB promises to address a longstanding bottleneck in the life sciences: the disconnect between data generation and data reuse. The project envisions a future where high-quality, large-scale molecular simulations are no longer restricted to elite research groups but are a universally available asset, fueling discoveries in biology, chemistry, and medicine.

The timeline for MD4SB spans four years, during which it will not only develop and deploy the integration platform but also benchmark its utility through real-world case studies involving both academic and industry partners. Through this collaborative validation process, the project expects to establish best practices, refine analytical tools, and build a sustainable infrastructure that institutionalizes molecular dynamics as a pillar of modern biomedical research.

In conclusion, MD4SB heralds a transformative chapter for the European research ecosystem by converging molecular dynamics with cutting-edge computational resources and artificial intelligence within a unified framework. Its success will empower scientists to decode the dynamic complexity of biological molecules at an unprecedented scale, accelerating drug discovery pipelines and fostering interdisciplinary collaboration in the era of data-driven bioscience.

Subject of Research: Molecular dynamics integration and infrastructure for structure-based biology, drug discovery, and biomedical research.

Article Title: MD4SB: Revolutionizing Molecular Dynamics Data Sharing and Integration Across Europe

News Publication Date: June 17, 2026

Web References:

• MD4SB project official website (to be launched)
• Horizon Europe funding portal
• IRB Barcelona: https://www.irbbarcelona.org/

Image Credits: IRB Barcelona

Keywords: Molecular dynamics, Structural biology, Supercomputing, Artificial intelligence, Drug discovery, Data infrastructure, FAIR data, Biomedical research, European Research Infrastructures, Computational biology